Page 2 of 7 FirstFirst 1234567 LastLast
Results 11 to 20 of 66

Thread: Brake Shoes

  1. #11
    Join Date
    Jul 2007
    Location
    Rhoadesville, Virginia (five miles from no place)
    Posts
    5,125

    Default

    Here is a NAPA link: http://www.napaonline.com/MasterPage...d=3&SubCatId=1

    This listing is for a 30 series rear brake shoe set on a P30 Chevy chassis....I also seem to recall they fit the J30 Jeep chassis too. They are 13" X 2.5" The Gladiator used them too:

    http://www.napaonline.com/MasterPage...d=3&SubCatId=1
    Last edited by randyscycle; September 22nd, 2008 at 06:42 PM.
    "Free advice is worth what you pay for it."™

  2. #12

    Default

    Before you go modifying civvie stuff.

    You can get the your current pads re-shoed from Memphis EQ, or buy all new ones - OE stock. No mods needed.

    Zach

  3. #13
    Jester Guest

    Default

    Thanks. Still confused but getting closer.

    Trying to decide if I should have them relined or modify the NAPA ones.

  4. #14
    Join Date
    Dec 2006
    Location
    Huntingtown,Md.
    Posts
    444

    Default

    Whatever happened to the post about using the chevy backing plate? I have been away, and lost it.

  5. #15
    Join Date
    Jul 2007
    Location
    Rhoadesville, Virginia (five miles from no place)
    Posts
    5,125

    Default

    Quote Originally Posted by vacca rabite View Post
    Before you go modifying civvie stuff.

    You can get the your current pads re-shoed from Memphis EQ, or buy all new ones - OE stock. No mods needed.

    Zach
    The reason I did the mod, was because when I called Memphis they wanted $25 per shoe for relined and my old ones in exchange. That is $100 per axle. $200 for the truck. Then I have to wait a week for UPS to bring the shoes and sit on the core charge for another week. I can buy brake shoes for my Deuce, which are twice that size for the same price, and outright with no core exchange. I think the M715 shoes are overpriced personally, but that is just my opinion.

    In this case, I had a few old GM axles laying around, stripped a set of old shoes and sent them back for the core on a $60 complete set of shoes which are readily available off the shelf. With a quick measurement, and less that 20 minutes, I had all four shoes modified to fit. The one time expense of $10 for the springs makes that a non-issue for future replacement. The switch to the E250 Ford wheel cylinders also assures that I will always be able to procure them locally as well.
    "Free advice is worth what you pay for it."™

  6. #16
    Jester Guest

    Default

    Quote Originally Posted by randyscycle View Post
    The reason I did the mod, was because when I called Memphis they wanted $25 per shoe for relined and my old ones in exchange. That is $100 per axle. $200 for the truck. Then I have to wait a week for UPS to bring the shoes and sit on the core charge for another week. I can buy brake shoes for my Deuce, which are twice that size for the same price, and outright with no core exchange. I think the M715 shoes are overpriced personally, but that is just my opinion.

    In this case, I had a few old GM axles laying around, stripped a set of old shoes and sent them back for the core on a $60 complete set of shoes which are readily available off the shelf. With a quick measurement, and less that 20 minutes, I had all four shoes modified to fit. The one time expense of $10 for the springs makes that a non-issue for future replacement. The switch to the E250 Ford wheel cylinders also assures that I will always be able to procure them locally as well.
    I am going with the E350 cylinders but am torn on the shoes. Can't find any in stock locally. I can have the stock ones relined locally for $23 a shoe.

    I dont have a core to exchange so the shoes run almost $70 plus still have to mod them.

  7. #17

    Default

    A 15 to 20 bucks relining, even 25 bucks, for my understanding is the better choise than to modify some civil parts. Original shoe is allways original. If you have the choise of instead 1/4 inch get a lining of f.e. 7 mm (only .65 mm thicker than 1/4 inch), you also pass the problems with the drum wear out.
    When I order brake shoes to be relined, I always ask for 7 mm thickness, even this is no standard measure for linings over here. Here you get 6 mm, 8 mm or 10 mm linings to be afixed to the shoe. The diffenence they grind down for no extra costs over here. We pay some 25 Euro per shoe and think that this price is fair, VAT of 19 % will be added!
    For this price we get asbestos free first quality lining material, heat resistant, low wear of the lining and less of the drum.
    Wolf

  8. #18
    Join Date
    Jan 2004
    Location
    Washington State
    Posts
    1,652

    Default

    Jester, I may have extras. You can have them and give me your old ones for cores. I think they are all good too. No lets see where did I see those again.

  9. #19

    Default

    I have some as well.

  10. #20

    Default

    You guys are late....Jester needed the shoes two years ago.....LOL
    Live like you will die tomorrow. Dream like you will live forever!!!

Similar Threads

  1. Brake shoes for dummies
    By fng in forum Stock Tech
    Replies: 18
    Last Post: July 27th, 2014, 01:07 PM
  2. oilcan : modified modern brake shoes for stock axles
    By oilcan in forum PseudoZone - Open Archive
    Replies: 4
    Last Post: November 11th, 2009, 03:06 AM
  3. Front brake shoes wet...
    By Fastfrankie in forum Open Discussion
    Replies: 5
    Last Post: August 17th, 2009, 08:23 PM
  4. wheel cyl and brake shoes need
    By angler in forum Modified Tech
    Replies: 3
    Last Post: May 21st, 2007, 10:07 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


Site Upgrade, Design Modifications & Administrative Support by:
Palm River Enterprises LLC, IT Solutions
President: Tom King, User ID=teking
This site is owned and operated by:
M715 Zone, LLC
President: Jon Schmidt, User ID=brute4c


If you have any suggestions, comments, problems or questions, contact:  brute4c@m715zone.com
Use of this site means you understand and agree to our TERMS OF USE

Copyright Notice:
This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com

Copyright 1998-2024