I know it's not much yet but my bed liner turned out awesome. The CUCV axles are in but I didnt take any pics. D70 & D60 w Detroit locker. Went with the duale axles to push the WWS out to run the 24 bolt HMMVW wheels w/ double bead lock inserts.
I know it's not much yet but my bed liner turned out awesome. The CUCV axles are in but I didnt take any pics. D70 & D60 w Detroit locker. Went with the duale axles to push the WWS out to run the 24 bolt HMMVW wheels w/ double bead lock inserts.
Last edited by teking; December 16th, 2020 at 12:02 PM.
Mating the LS1 to the sm465 and np205. FYI NO adapter necessary to mate the SM465 to the LS1. LS flywheel, 12" plate, and a LS7 pilot bearing to compensate for the LS crank offset from typical 350. Standard manual bellhousing.
https://www.youtube.com/watch?v=YuS8h4hshe4
LUK 04064 Clutch kit - Rockauto $75.99 12”, 10-spline, 1 1/8” input shaft, w/throwout
or
NU 1909 Clutch Kit – Autozone $84.99 12”, 10- spline, 1 1/8” input shaft, w/throwout
Sachs NFW 1050 Flywheel - AutoZone $99.99
LS2/LS7 pilot bearing - 12557583 – AutoZone $23.99
ARP 330-2802 flywheel/crank – Amazon $40.38
ARP 134-2203 Pressure plate / flywheel – Amazon $29.79
Last edited by teking; December 17th, 2020 at 01:39 PM.
Looks great, look forward to seeing more.
All mocked up and sitting on the new engine and tranny Mount locations. Had computer reprogrammed so it knows its not a 2001 Corvette .... LOL
Last edited by teking; December 17th, 2020 at 01:40 PM.
Borgeson steering conversion. Followed instructions on this board. Ordered the very part numbers recommended from the site. Dead on.
Stock Steering Coupling Bell-Shaped thingy elimination
Last edited by teking; December 17th, 2020 at 01:19 PM.
SM465/NP205 slid right in with new cross brace. Also got the Grant steering wheel part numbers from this board especially the correct adapter part #. And again dead on. If you look close you can see the TAC module and fly-by-wire gas pedal sitting on the drivers floor ready to get mounted up.
Steering wheel adapter
Last edited by teking; December 17th, 2020 at 01:36 PM.
SM465 clutch linkage fabrication.
All 12V. Now!!
Sent from my SM-G781V using Tapatalk
J truck seat. Ted towel while working on cab.
Sent from my SM-G781V using Tapatalk
Clean as a whistle and sharp as a knife...beautiful!
Lord send your Holy Ghost into our hearts and make the desire of our hearts Your Will.
Pro-choice, that's a LIE, babies don't choose to die!!
Site Upgrade, Design Modifications & Administrative Support by: Palm River Enterprises LLC, IT Solutions President: Tom King, User ID=teking |
This site is owned and operated by: M715 Zone, LLC President: Jon Schmidt, User ID=brute4c |
Copyright Notice: This web site is subject to the protection of the copyright laws of the United States and other countries. Except for Personal Use Only, you may not modify, copy, distribute, transmit, display, perform, reproduce, publish, license, create derivative works from, transfer, or sell any information obtained from any part of the M715 Zone website without the prior written permission of M715 Zone, LLC. Written permission can only be obtained by contacting brute4c@m715zone.com |